Trunk Medallion?
3/19/10, 05:18 AM
#66
Shelby GT350 Member
Here's a picture of my new parts I installed last weekend. It's the SHR blackout panel and rear medallion with the Shelby CS Supercharged logo and the slotted taillight covers from Moss ...
Joseph , that looks great ... I personally think it would look even better with the SHR panel around it , but then I'm biased ...
Joseph , that looks great ... I personally think it would look even better with the SHR panel around it , but then I'm biased ...
3/21/10, 10:40 PM
#69
Team Mustang Source
Center Steering Wheel Emblem Replacement
Hey I have been following your thread, have you decided how to do the steering wheel cap, I am interested, but don't want to remove the current one, an overlay would be nice. You did a really good job on yours..
GG
---------------
I don't know about that steering wheel cap. I think it might be too tricky to work with that thing. It appears to be possible to pry it off, but you may not ever get it back just right. Or, get something else to lay down so well in that recess. I think I'm OK with the running pony for now.
Joe
GG
---------------
I don't know about that steering wheel cap. I think it might be too tricky to work with that thing. It appears to be possible to pry it off, but you may not ever get it back just right. Or, get something else to lay down so well in that recess. I think I'm OK with the running pony for now.
Joe
If anyone else has done this please post pics, some have just placed a decal over the saleen disk, I'm going to have a disk made for my BJ
GG
3/22/10, 09:20 AM
#70
Bullitt Member
Join Date: April 24, 2008
Location: Graysville
Posts: 221
Likes: 0
Received 0 Likes
on
0 Posts
Here's a picture of my new parts I installed last weekend. It's the SHR blackout panel and rear medallion with the Shelby CS Supercharged logo and the slotted taillight covers from Moss ...
Joseph , that looks great ... I personally think it would look even better with the SHR panel around it , but then I'm biased ...
Joseph , that looks great ... I personally think it would look even better with the SHR panel around it , but then I'm biased ...
12/15/10, 11:42 AM
#75
Member
Join Date: August 30, 2008
Location: Camp Fallujah, Iraq
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
After watching this thread, decided to paint Faux cap flat black with an LED MOD like the example shown. Got some ideas, but will work this out so it looks well done when fiished. Not sure what to do with the center emblem, but if I place an emblem, I think it would look nice illuminated also...
Could be lighted with parking lights or with third brake light... not sure yet.
Could be lighted with parking lights or with third brake light... not sure yet.
1/3/11, 02:35 PM
#78
Bullitt Member
Join Date: May 21, 2010
Location: San Diego, CA
Posts: 203
Likes: 0
Received 0 Likes
on
0 Posts
I'll throw mine up here, now that I have a few photos of it.
Blacked out the center section, and overlaid a 1968 GT badge on it. It matches the same badges that I have on the front fenders. The badges are concave (to match the center caps it came off of), so I had to flatten them out as best I could. The most tedious part was applying thin strips of double-sided trim tape before putting them on the car.
Blacked out the center section, and overlaid a 1968 GT badge on it. It matches the same badges that I have on the front fenders. The badges are concave (to match the center caps it came off of), so I had to flatten them out as best I could. The most tedious part was applying thin strips of double-sided trim tape before putting them on the car.
1/3/11, 03:41 PM
#80
Legacy TMS Member
