Anyone have Autopower roll bar in S197 vert
#3
Legacy TMS Member
Thread Starter
The only one I could find was of the Maximum Motorsport 50 for a pre S197 Mustang and not the Autopower. Perhaps I missed that one but as of yet I can't find it.
Thanks
BB
Happy 231st all you fellow Devil Dogs.
Thanks
BB
Happy 231st all you fellow Devil Dogs.
#4
I ran into the same problem trying to find a rollbar for my vert. In the end, I had a local shop fab one based on a design I copied from CDC's lightbar.
http://i46.photobucket.com/albums/f1...00_0302_00.jpg
http://i46.photobucket.com/albums/f1...100_0347-2.jpg
http://i46.photobucket.com/albums/f1...00_0302_00.jpg
http://i46.photobucket.com/albums/f1...100_0347-2.jpg
#5
Join Date: April 12, 2005
Posts: 399
Likes: 0
Received 0 Likes
on
0 Posts
I ran into the same problem trying to find a rollbar for my vert. In the end, I had a local shop fab one based on a design I copied from CDC's lightbar.
http://i46.photobucket.com/albums/f1...00_0302_00.jpg
http://i46.photobucket.com/albums/f1...100_0347-2.jpg
http://i46.photobucket.com/albums/f1...00_0302_00.jpg
http://i46.photobucket.com/albums/f1...100_0347-2.jpg
#6
Legacy TMS Member
Thread Starter
BB
#7
Join Date: April 12, 2005
Posts: 399
Likes: 0
Received 0 Likes
on
0 Posts
1) all points must have 6"x6"x1/8" thick steel plates that sandwich the floor pan. The plates are retained using at least three 3/8" grade-8 bolts at each of the four mounting locations.
2) There is no crossbar for seatbelt mounting.
3) There is no 5th bar as shown in the picture
2) There is no crossbar for seatbelt mounting.
3) There is no 5th bar as shown in the picture
#8
Legacy TMS Member
Thread Starter
I'm not looking for a 5 point, I won't be drag racing. At most I will autocross and I hope the 4 point Autopower with detachable diagonal and horizontal support will suffice. I do like the unobtrusive look of the CDC light bar and if I could find a 4 point that only showed the vertical loop above the door sills, I would go for it. I've never rolled a car but I've responded to hundreds of traffic accidents over 17 years as a volunteer firefighter. Most rollovers were on their sides and the few that continued rolling didn't stop on their tops. Even with all of these accidents I never responded to a convertible rollover, which due to it's design would probably stop on it's top. NHTSA only listed 92 fatalities to convertible rollovers for 2004 so I'm not sure if I even need a rollbar as I don't believe SCCA requires one for Solo II.
BB
BB
#9
how about a coupe
I ran into the same problem trying to find a rollbar for my vert. In the end, I had a local shop fab one based on a design I copied from CDC's lightbar.
http://i46.photobucket.com/albums/f1...00_0302_00.jpg
http://i46.photobucket.com/albums/f1...100_0347-2.jpg
http://i46.photobucket.com/albums/f1...00_0302_00.jpg
http://i46.photobucket.com/albums/f1...100_0347-2.jpg
I really like your layout.
Thread
Thread Starter
Forum
Replies
Last Post
Gigantor
2005-2009 Mustang
31
5/11/23 07:31 PM